M-Factors

M-Factors 2.5" SATA Kioxia/Toshiba 15nm MLC SSD 32GB, 64GB

M-Factors 2.5" SATA Kioxia/Toshiba 15nm MLC SSD 32GB, 64GB

$20.00
  • SKU: E911 32GB
  • Availability: Usually ships in 1-3 days
  • Shipping: Calculated at Checkout
Availability: Usually ships in 1-3 days
In Stock & Ready To Ship!
Current Stock:Only left:
Description

M-Factors 2.5" 32GB/64GB SATA MLC (Toshiba 15nm) SSD 

M-Factors 2.5" 32GB SATA SSD delivers all the advantages of Flash Disk technology with Serial ATA I/II/III interface and is fully compliant with the standard 2.5" form factor. The device is designed based on the standard 7-pin interface for data segment and 15-pin for power segment. The 2.5" SATA runs at a maximum operating frequency of 300MHz with 40MHz external crystal. Based on Toshiba's MLC flash (with external DDRIII 256MB/512MB cache enabled and measured by CrystalDiskMark v3.0), Emperor 900 can reach up to 450MB/s read as well as 300MB/s write high performance. Moreover, the 2.5" SATA SSD enables hot-swapping when removing, replacing, or upgrading flash disks while also providing low power consumption in comparison to traditional hard drives.

Offering improved Read/Write performance, SMART technology, reliability, and low power consumption, E911 2.5" SATA SSD is an ideal storage for embedded systems.

HIGHLIGHTS

  • Easy installation
  • Toshiba MLC 15nm NAND Flash
  • Compliant with SATA Revision 3.0
  • Compatible with SATA 1.5Gbps, 3Gbps, 6Gbps interface
  • NCQ support up to queue depth=32
  • Supports power management
  • Supports expanded register for SATA protocol 48 bits addressing mode
  • Embedded BIST function for SATA PHY for low cost mass production
  • Supports all types of MLC large block: 16K/page NAND Flash
  • Supports 2.3 interface and 3.0 interface: 5 channels at maximum
  • Contains 4pcs to 16pcs of TSOP Flash
  • Corrects up to 72bits error in 1K Byte data
  • Supports SMART and TRIM Commands

 

 ***Optional Industrial Grade supporting -45C to 85C and SLC is available (Contact 949.617.0080 or support@mfactors.com) 

Item

Specification

Specification

Interface

SATA 6Gbps and 3Gbps, 1.5Gbps interface

ONFI 2.3 and ONFI 3.0 Interface support 

Electrical 5V (Operating Voltage)

Form Factor

2.5" SATA

SIze

Option 1: 100mm*69.85mm*7mm

Option 2: 100mm*69.85mm*9.5mm

weight

~2oz/0.13lbs

Capacity

32GB

Performance

Sequential write

300 MB/s

Sequential Read

450 MB/s

Power Dissipation

Idle

105mW  

Active 

2560mW 

Dependability

TRIM 

support 

NCQ 

support 

Firmware Update 

support 

MTBF

>1,000,000 hours

S.M.A.R.T

support

Bad-Block Management

Advanced bad sector management algorithms

Wear-leveling

Static and dynamic wear-leveling algorithms

ECC

Built in hardware ECC circuit (up to 72bit/1KB)

Environment

Storage temperature

-40~85℃

Operation temperature

Standard

0~70 ℃

 

 

 

 

Vibration 

80Hz~2000Hz/20G 

Shock

1500G/0.5ms

Humidity

90% under 40C

TBW

Terabytes Written: 35TBW for 32GB

RoHS Compliant

Yes